The Siren in Stainless Steel Enclosure 118dB is a self-contained siren in a tamper and corrosion-resistant stainless steel enclosure. It features two sealed reed tamper switches: one on the backplate and one on the front cover. Additionally, the switches are normally closed as well as pre-wired in series. The Siren in Stainless Steel Enclosure 118dB can also produce two distinct sounds from a single input trigger.

The stainless steel exterior also reflects the color of the mounting surface, allowing the Siren in Stainless Steel Enclosure 118dB to blend easily with any residential or commercial building.

The ComboTrigger™ option also allows controls, which have a single alarm output and pulsing option to activate both the burglar and fire alarm sounds.

In addition, this Siren is also compatible with all hardwired panels, including Vista and DSC.

Features:

• Installer Friendly – Easy to Mount – Exterior / Interior use
• Sealed Reed Tamper Switches at single-bolt closure and at the rear of the cabinet
• Corrosion-resistant stainless steel construction
• Compact – Less Noticeable
• Loud – Rivals Sound of Larger Speakers
• Heavy Duty 1.8 lb Magnet
• ComboTrigger™ For Single Outputs
• Pre-Wired For Easy Installation

Specifications:

• Operating Voltage: 6 to 14 Volts DC
• Current Draw: 1.2 Amps
• Sound Level: 118 dB @ 1 meter, 14 Vdc
• Enclosure: #304 Stainless Steel with Stainless Hardware Included
• Size: 5″ H x 5″ W x 4″ D
• Lifetime Limited Warranty

Instructions:

The Siren in Stainless Steel Enclosure 118dB is a self-contained siren in a tampered, corrosion-resistant stainless steel enclosure. It also incorporates two sealed reed tamper switches for enhanced reliability and ease of use.

1. Using the backplate as a template, mark and drill the 4 mounting holes and the wire or conduit entry hole. Insert the (4) 1/4 x 1” wall anchors, then partially install the top two #10 x 1” screws.

2. Route the wire or conduit through the hole provided and hang backplate on the top screws. Then install the remaining two screws and & tighten all four.

3. Temporarily hang the Siren/speaker on the backplate by aligning the slotted insert on the top edge of the Siren with the 1/2” recessed tab on the bottom edge of the backplate. Then press Siren onto the tab.

4. Connect the two white wires from the tamper switches to a 24 hour closed loop on the control panel (the switches are already connected in series).

5. Connect the Red (+) and Black (-) wires from the Siren to the control’s alarm output. The Siren produces a Yelp sound from a constant voltage input. If the voltage input is pulsed, the siren produces a low pitch rise. This ComboTriggerTM feature also allows two sounds to be activated by a control that has only a single alarm output with a pulse option. The recommended wire gauge from control is 18 AWG. NEG (-) Black = Negative (-) terminal from Control’s Alarm output. YELP (+) RED = Positive (+) terminal from Control’s Alarm output

6. Move the Siren/speaker from its hanging position to its final mount by aligning its top and bottom slots with the 1/2” tabs on the top edge of the backplate and in the bottom center above the bolt threads. Then press firmly.

7. Slide front cover over the speaker. Lift up to engage the tabs in the cover with the two “U” shaped slots on the top edges of the backplate. Lower cover until tabs are in slots. Push the cover towards the wall, then lift up to lock tabs in slots. Thread 1/4-20 hex bolt into the hole on the bottom of the cover and tighten until secure.

8. The front cover tamper switch is pressed closed by the front cover during the final 3 to 4 full turns of the hex bolt. If possible, test the operation of the tamper switch using a continuity meter.

Note:

Siren in Stainless Steel Enclosure 118dB is designed for Single Output Alarm Controls that use a STEADY Output for BURG or a PULSING Output for FIRE. For an Alarm Control panel that has separate BURG and FIRE, alarm outputs connect the Red wire to each output, then program one output for Steady(Burg) and the other for Pulsing(Fire). Then connect the Black wire to Neg.

This hardwired siren is compatible with the Vista 20P Panel, the DSC Neo Panels, the IQ Pro Panel, and the Power G Hardwire Module.

If this siren isn’t what you need, check out our other sirens.

Check out our youtube channel for more information.